|












Etched Glass Decals
The look of
real etched glass for a fraction of the cost!
Vinyl Etchings
Decals are:
Easy to Use!
Easy to apply!
Removable & Reusable!
Decals cling on to any
smooth glass surface.
Click
Etched Decals
to view all of our designs.
Great Purse
Jewelry!
Finders Key Purse®
Key Chains

Find your keys
quickly with our stylish
Purse Jewelry Finders Key Chains!

A convenient way to locate your keys at a
moment's notice as well as a beautiful charm for your purse, backpack, briefcase
or pocket.
Decorative hook sits
on the outside of
your purse with keys
safely inside.
3-D Fly-Thru Window
Magnets


3-D Fly Thru
Window Magnets
Looks like they
are flying through
your window!
To see all of our
3-dimensional Fly-Thru's
Click Fly Thru
Window Magnets.
Contact Us
Please feel free to email us with any questions you may have and we'll be happy
to help you.
| |

Self-Adhesive Glass Film Instructions
NOTE: Read All Instructions Before Application
(This is a simple process! However, preparation is very important.)
Tools Needed:
Scissors/Razor Knife, Tape Measure/Ruler, Squeegee,
32 oz Spray
Bottle,
Lint-free Paper Towels, or Soft Lint-free Cloth (Micro-fiber)
1.
Clean all areas where the film is
to be applied, removing all traces of dirt, grime, grease, etc.
2. Carefully
measure height and width of the area of application. Cut film to fit or,
cut 1” wider
and
1” longer, then trim film for exact fit once applied to surface and after
first squeegee process.
3. Use film-aid
application concentrate, if available by your dealer, or create your
own wetting
solution
by
adding a few drops (only a
one-second squeeze)
of either Johnson Baby Shampoo or
Joy Dish Detergent into a 32 oz spray bottle and then fill with water.
4. Turn off all
fans and any AC/heating ventilation ducts in your working area.
5. Lay the
cut-to-size decorative film on a clean flat surface with the release liner
up, or have
someone
hold piece to be applied for you. Remove the release liner. (See "Tips"
below for easy
liner removal.)
Spray the now exposed adhesive film surface thoroughly with wetting
solution.
Note: when using the
larger-sized film (36” x 76”), two people will be needed for easy
application.
6. Next apply a
generous amount of wetting solution to the glass. Make sure it's dripping
wet; too
much
solution is better than not enough! And, by wetting both the film and
glass, it prevents the
film from
sticking to itself and to the surface immediately, thereby allowing you more
time in which
to properly
position the film. If either surface become dry before applying,
rewet them completely.
7. Place the wet
adhesive side of film against wet glass surface. Start at top of surface,
then allow
film to
gently lay down on the glass. You can slide film around positioning it
correctly so long as the
window and film
remain thoroughly wet. For ease in squeegee process, lightly spray the face
of the
film. Now start to squeegee
out wetting solution, working from the center out toward the edges.
Double
check that the film is flat and
smooth with no remaining air bubbles. It may be necessary to
again spray
the face of the film and squeegee to
release any remaining moisture.
8. If, at this
point you did not cut the film to exact size, use your ruler to trim along
edges with a
straight edge
razor. It is ideal to cut in one continuous movement and to use a new blade
tip after
3-4 cuts. Carefully dry any
excess wetting solution that appears around the edges.
TIPS:
The film begins to
adhere in 30 minutes and cures fully over 3-5 days. During the drying
process,
it could initially
look hazy, cloudy, or spotty. However, this effect will disappear over a
short time.
Dry, sunny weather speeds
curing while wet and/or cold temperatures may possibly prolong it.
All decorative
adhesive films have a liner applied to the back of it. To easily remove
liner, apply a
piece of tape
on a corner edge and another on the same edge of the backside of the film.
As you peel
tape apart, liner should
peel away. Caution:
Take care as you remove the release liner and do not let
the film roll over
on to itself as it
will stick together and be difficult to pull apart.
A stubborn,
remaining air bubble or two that have not been worked out during your final
squeegee
process can
be removed by using a straight pin to pop and then work out the air gently
with your finger.
To clean the film, a
very light, mild soapy-water solution should be used and then wipe over with
a soft, damp cloth. DO NOT USE AMMONIA, VINEGAR, HOUSEHOLD GLASS CLEANERS, PAPER TOWELS,
BRUSHES
or any other item that may scratch or damage the film.
Window film absorbs
up to 98% of the harmful ultraviolet (UV) rays thereby protecting your
furnishings
and aids in glare and heat reduction. Light is dispersed softly,
rendering tranquil atmosphere, which reproduces
a beautiful etched-glass appearance not typically found in window films.
When properly
applied and cleaned, your decorative film will give you years of enjoyment,
privacy and increases personal safety from glass breakage.
Overall product life is affected by climate, geographic location, and
exposure to the sun.
Removal is easy.
It
can be peeled away and for larger areas, you may want to spray with an
adhesive remover first.
Print Instructions for future use.

Easy to apply!

|